Sensor uses 2D material to enable sharp low light cellphone photos
A team of Penn State researchers has found that a new type of active pixel sensor that uses a novel two-dimensional material may both enable ultra-sharp cellphone photos and create a new class of extremely energy-efficient IoT sensors.
“When people are looking for a new phone, what are the specs that they are looking for?” said Saptarshi Das, associate professor of engineering science and mechanics and lead author of the study published in Nature Materials. “Quite often, they are looking for a good camera, and what does a good camera mean to most people? Sharp photos with high resolution.”
“When you take an image, many of the cameras have some kind of processing that goes on in the phone, and in fact, this sometimes makes the photo look even better than what you are seeing with your eyes,” Das said. “These next generation of phone cameras integrate image capture with image processing to make this possible, and that was not possible with older generations of cameras.”
However, the great photos in the newest cameras have a catch — the processing requires a lot of energy.
“There’s an energy cost associated with taking a lot of images,” said Akhil Dodda, a graduate research assistant at Penn State at the time of the study who is now a research staff member at Western Digital, and co-first author of the study. “If you take 10,000 images, that is fine, but somebody is paying the energy costs for that. If you can bring it down by a hundredfold, then you can take 100 times more images and still spend the same amount of energy. It makes photography more sustainable so that people can take more selfies and other pictures when they are traveling. And this is exactly where innovation in materials comes into the picture.”
The innovation in materials outlined in the study revolves around how the researchers added in-sensor processing to active pixel sensors to reduce their energy use. To do this, they turned to a novel 2D material, which is a class of materials only one or a few atoms thick, molybdenum disulfide. It is also a semiconductor and sensitive to light, which makes it ideal as a potential material to explore for low-energy in-sensor processing of images.
“We found that molybdenum disulfide has very good photosensitive response,” said Darsith Jayachandran, graduate research assistant in engineering and mechanics and co-first author of the study. “From there, we tested it for the other properties we were looking for.”
These properties included sensitivity to low light, which is important for the dynamic range of the sensor. Dynamic range refers to the ability to “see” objects in both low light such as moonlight and bright light such as sunlight. For example, the human eye can see stars at night better than most cameras due to having superior dynamic range.
Molybdenum disulfide also demonstrated strong signal conversion, charge-to-voltage conversion and data transmission capabilities. This makes the material an ideal candidate to enable an active pixel sensor that can do both light sensing and in-sensor image processing.
“From there, we put the sensors into an array,” Jayachandran said. “There are 900 pixels in a nine square millimeter array we developed, and each pixel is about 100 micrometers. They are much more sensitive to light than current CMOS sensors, so they do not require any additional circuitry or energy use. So, each pixel requires much less energy to operate, and this would mean a better cellphone camera that uses a lot less battery.”
The dynamic range and image processing would enable users to take sharp photos in a variety of adverse conditions for photography, according to Das.
Das noted that the three main facilities in the Materials Research Institute were instrumental in creating and testing the material.
“The 2D materials we used for the experiments were grown at the Two-Dimensional Crystal Consortium facility at Penn State which is a National Science Foundation Materials Innovation Platform (MIP) facility, the characterization of the material was done in the Materials Characterization Laboratory, and we also used the cleanrooms in the Nanofabrication Laboratory,” Das said. “Having easy access to these facilities right on campus played a major role in making this research successful.”
Along with enabling a top-rate phone camera in the future, the team also envisions their improved sensor technology could have other applications. This would include better light sensors for Internet of Things and Industry 4.0 applications.
“Sensors that can see through machines while in operation and identify defects are very important in the IoT,” Dodda said. “Conventional sensors consume a lot of energy so that is a problem, but we developed an extremely energy efficient sensor that enables better machine learning, and saves a lot in energy costs.”
Along with Das, Dodda and Jayachandran, other authors of the study include from Penn State Andrew Pannone, Nicholas Trainor, Sergei Stepanoff, Megan Steves, Shiva Subbulakshmi Radhakrishnan, Saiphaneendra Bachu, Claudio Ordonez, Jeffrey Shallenberger, Joan Redwing, Kenneth Knappenberger and Douglas Wolfe.
The work was supported by the Department of Defense and the National Science Foundation.
DOI: https://doi.org/10.1038/s41563-022-01398-9
Related articles
Partnership to use quantum sensors to control satellites
Sensor-to-satellite technology for global IoT connectivity
Ultra-compact 60 GHz ranging sensor with signal processing
If you enjoyed this article, you will like the following ones: don't miss them by subscribing to :
